Skip to main content

Filter By:

  • Show More Sizes
  • Show Fewer Sizes

Indoor Cycling

CycleOps Trainer Bag
$80.99
When you need to transport your trainer, CycleOps' Trainer Bag is the most convenient solution. There is no need to worry about your trainer getting damaged when it's safe and secure on the way to your race or event.
Kinetic Old Small Wheel Adapter
$64.99
For use with T-002I, T-016, T-007, AND T-006C trainer models. A must for BMX, recumbents, and any bike with tires having an outside diameter of 16 to 22 inches. The small wheel adapter raises the level of the resistance unit of compatible Kinetic Trainers by up to three inches.
Kinetic Internal Chain Actuated Cone Cup
$26.99
The Internal Chain Actuated Cone Cup is designed to work with chain actuated internal rear hubs, including Sturmey Archer. It also works perfectly with pre-2018 Brompton folding bicycles.
Kinetic Threaded Shallow Cone Cup
$24.99
This cone cup replaces the threaded cone cup on pre-2013 Rock and Roll trainers and is the mounting solution for carbon Trek Speed Concept frames that require a smaller cone cup on the drive side of the trainer than the pre-installed version. - Only compatible with the Rock and Roll trainer - This cone cup's smaller outside diameter fits makes it compatible with carbon Trek Speed Concept bikes (aluminum Speed Concept bikes are compatible with the Standard Cone Cup) - Use this cone cup on the drive-side of the Rock And Roll trainer (it is not necessary to replace both cone cups)
Robert Axle Project Trainer Thru Axle
Our Trainer Axle is designed to adapt your thru-axle equipped bike to on-wheel trainers, such as a 1up, Blackburn, Cyclops, Kinetic, Tacx, Wahoo, and many others. Our goal is to fit the thru-axle to your bike perfectly to minimize spacers and extra parts, providing a clean, high-performance axle for your bike. Train, warm up, and be race ready and fit for the season. - When it’s time for your race or time to head outside, simply remove your bike from the trainer, remove the drive side axle end and go. Our axle is suitable for use on or off the trainer, indoors or out. - The axle shaft and axle ends are precision CNC-machined from 7075 aluminum and hard-anodized for rugged durability. - No special tools required. Design allows for installation or wheel removal using your standard 5mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world. Important: Before you order, make sure your specific trainer will accommodate the width of your modern thru-axle-equipped bike. Measure your trainer at the widest setting and measure the outside width of your bike frame. Our the trainer axle ends will extend past your frame on each side.
Tacx BlackTrack
$299.00
The BlackTrack replaces the Skyliner (front wheel support) and enables you to steer freely in the Tacx Trainer software 4, Advanced. The front wheel of the bike is placed on a turntable so that you can steer to the left and the right. This allows you to choose where to ride when you are training in the virtual worlds. The BlackTrack communicates wirelessly with the computer via ANT+. Rubber Caps on the bottom prevent sliding and reduce noise. This steering frame is foldable. lightweight, and easy to store. The BlackTrack is suitable for the Tacx Trainer software (Windows PC) and can communicate with ANT+ trainers and interactive Smart trainers: - T1980 Bushido (ANT+) - T2020 i-Genius - T2050 Tacx IRONMAN trainer - T2060 Tacx IRONMAN Smart - T2080 Genius Smart with Upgrade Smart - T2170 i-Vortex - T2180 Vortex Smart with Upgrade Smart - T2240 Flow Smart with Upgrade Smart - T2780 Bushido Smart with Upgrade Smart
Tacx Direct Drive Freehub Body, Campagnolo
$114.99
This freehub body enables you to fit a Campagnolo cassette on the NEO Smart and the FLUX Smart. Suitable for 9 through 11 speed Campagnolo cassettes. How to place the Campagnolo Body: 1. Remove the cap with a 5-millimeter Allen key. 2. Replace the Shimano/SRAM body with the Campagnolo body. 3. Place the cap on the Campagnolo body and tighten with a 5-millimeter Allen key.
Kinetic Standard Cone Cup
$14.99
This cone cup is for quick-release bikes and is designed to work best when used with the Kinetic Skewer included in the box with every trainer.
Tacx E-Thru Trainer Axle
$49.99 - $65.00
The E-Thru Trainer Axle allows the use of a mountain bike in a Tacx trainer. These axles are only suitable for Tacx classic trainers.
CycleOps Magnetic Remote Shifter
$40.49
CycleOps' Magnetic Remote Shifter is for use with CycleOps' standard Mag trainers. It allows you to adjust the resistance without leaving the saddle and fits on your stem or handlebars.
Tacx Trainer Bag
$139.99
Give your Tacx trainer the best possible protection for storage and transport with this sturdy trainer bag. It's designed specifically for Tacx trainers and has a separate compartment on the inside for accessories. The double inner layer with foam lining provides optimum protection, minimizing the risk of damage.
Kinetic Slotted Cone Cup
$14.99
This cone cup is designed to work best when used with the Kinetic Skewer included in the box with every trainer. - Each new trainer ships with one of the Slotted Cone Cups installed on the non-drive side of the trainer - When installing, be sure to place the cam-end of the skewer in the slotted cone cup
Saris Aluminum Roller
$399.99
Take on any race, club ride, or weekend adventure with confidence. When you add Saris rollers into your training routine, you'll increase your balance, control, and ability to ride a straight line — all of which translate to more efficiency, power, and technique on the road. And, because you have to pedal 100% of the time to balance your bike, you get an amazing workout, no matter your pace. - Improve balance, control, and ability to ride a straight line. - Aluminum roller drums run silently and smoothly. - Precision-lathed 3.25" aluminum roller drums won't distort in heat or sunlight. - Fold flat or stand on end for convenient storage. - Designed for both indoor and outdoor use - 16" wide wheel base fits just about any size of bike and allows plenty of room to move around. - Rubber foot pads ensure that the only thing moving on the rollers are the drums, providing a secure, sturdy ride. - Durable steel-frame construction - Adjustable belt for right and left dismount - Resistance Roller uses zero moving parts to deliver quiet magnetic resistance. - Maximum wheelbase 44.5" (axle to axle) - Minimum wheelbase 37.5" (axle to axle)
Tacx Trainer Adapter for X-12 Axle
$64.99
The Trainer Adapter for X-12 Axle allows the use of mountain bikes with axle widths of 142mm or larger on a Tacx trainer. These adapters are only suitable for the Tacx classic trainers.
Page 1 of 1